Nate Custom Boat

I'm running 5/8 ply with EVA foam what size hinge would work with it?

It's recommended to go with a 1" offset hinge. Product link:. OFFSET HINGES

Can you send me the dimensions for the double mount with no accessories?

All of the dimensions on the double graph mount can be found in this video - https://youtu.be/0fj80QX_QKk. Product link:GRAPH MOUNTS - TBNATION

How high does the double graph mount be set at the fastening feet?

There are two options, either a 5" or an 8". The 5" was our standard. We created the 8" for guys who like to wear boots while fishing.Product link:GRAPH MOUNTS - TBNATION

What size graphs are compatible with this double graph mount?

12" Graphs are the largest we have tried on the Gen2 Double Graph Mount. Usually we put a 12 and 10", rarely two 12".

Does the Trolling Motor Mounting Bracket need to be bolted to the front of the boat also?

Yes, usually this is done with rivets, either standard or countersink.Product:TROLLING MOTOR MOUNTING BRACKET

What's the size dimensions on the gear caddy and trolling Motor Mount Caddy?

Corner Caddy is 11 x 11", Trolling Motor Mount Caddy is 18". Product link:CORNER CADDY - GEARGEAR CADDY - TROLLING MOTOR BRACKET

What gage or thickness is the Aluminum Angle in the starter kit?

All of our angle and tube aluminum is 1/16" in diameter. Product link:BUILD FROM SCRATCH - ALUMINUM FRAMING KIT

I’m looking at buying the aluminum welded 18 gal live well. I’d like to know what size the drain hole is and what kind of 90 degree fitting you Guys recommend?

The drain hole is made to accept a 3/4" thru hull fitting. The drain fitting we use comes in the that can be purchased with the livewell tank. Product links: FLOW-RITE LIVEWELL PUMP KIT - PREMIUM SETTHRU-HULL BRACKETS FOR 3/4" THRU-HULL FITTINGS

What grade is you aluminum?

Sheeting is 5052 and other material is 6061.Product links:. ALUMINUM TRANSOM REPLACEMENT KITALUMINUM SHEET 6-PACK

What size hardware do you suggest I use to mount?

3/8" Stainless steel Bolt OR larger.

What size hole do I need to cut into my deck?

The recessed foot tray fits into a 9.75" x 17" hole in your deck.

What size of Offset hinge do I need?

Wood thickness: 1/2" - 3/4" offset ; Wood thickness 3/4" - 1" offset. Product link:. OFFSET HINGES

What are the dimensions of Double cup and phone gear caddy?

This is 14.5" Long, 5.75" wide at the top, and 7.5" wide at the bottom bc there is a little bump out at the bottom. Product link:DOUBLE CUP AND PHONE GEAR CADDY

On your hatches, where does the rain water collect?

There is a drain port on the dry track of the lid that connects to a 1/2"rubber hose that you can direct to any area where you would like to expel the water. I will inform you though, that these hatches are not 100% waterproof. There is potential for

What type of aluminum is your 2"x2"x1/16" framing aluminum, 6061-T6 or 6063-T52?

The 2 x 2 angle aluminum is 6061. Product link:. ANGLE ALUMINUM FRAMING

How wide is the gen2 dual mount at the bottom where it mounts to the boat?

The inside mounting is 12.25" the outside of the mount area is 14.75".

What is framing rough opening dimensions?

Dry Hatch frame opening dimensions are 1/2" bigger than the lid size. Example: 12 x 24" Dry Hatch - Hole size 12.5" x 24.5".Product link:DROP-IN DRY HATCH LIDS - PRE-BUILT

What is the thickness measurement of the dry hatch lids' lip?

The lip thickness is .090. Product link:DROP-IN DRY HATCH LIDS - PRE-BUILT

Do you have an installation video for graph mounts?

"We don't have an actual "installation" video, but we do have a video describing the product and it shows what the final product should look like. Take a look at this video and see if this helps!. Graph Mount Video - https://youtu.be/0fj80QX_QKk

Can a double graph mount hold a Helix12?

No, you will want the Gen 2 Double Graph Mount, it will hold the 12".

Is there any ware issues on the two rivets? I have a 1980-ish Mirror Craft and was looking to do something like the Weekend Warrior build.

To our knowledge, there are not any ware issues on the rivets when attaching the subfloor framing to the ribs. They get connected the same way we connect the other rivets in the boat. You will want to vertically support the framing in the middle if p